Reply to thread

Message: [QUOTE="Shamiso, post: 93131, member: 160"] Pro Tools can feed a bus into a compressor’s key input so one track controls gain reduction on another. Sidechain compression in Pro Tools is therefore mostly a routing job before it becomes a compressor-settings job. The audio you want to turn down stays on its own track, while a separate trigger signal tells the compressor when to react. For the stock route, insert Dyn3 Compressor/Limiter on the track you want reduced. Dyn3 sits inside the [URL='https://goldmidi.com/community/threads/how-often-do-any-of-you-use-avid-pro-tools-dynamics-iii-plugin-suite.5016/'][B]Avid Pro Tools Dynamics III plugin suite[/B][/URL] and accepts an external key signal. The trigger does not need to pass through the target track’s audible signal path, which is the bit that makes sidechaining useful rather than just ordinary compression. Sidechain compression is not necessary by default. If two parts already fit, ducking one simply changes a balance that was working. The useful reason to reach for it is a repeatable collision, rhythmic movement, or a foreground part that needs temporary space without permanent EQ cuts. [HEADING=2]The routing has to work before the compressor does[/HEADING] Setting up sidechain compression in Pro Tools starts with a send from the trigger track to an available bus. Open the compressor on the target track, choose that same bus as the Pro Tools sidechain input, then enable the external key. If the gain-reduction meter never reacts, check the send, bus assignment, key input, and key enable state before touching threshold. The same signal flow applies when you want to sidechain a plugin in Pro Tools for more than kick-and-bass ducking. A vocal can trigger compression on a music bus, a dry vocal can control an effects return, and a percussion track can drive a gate. One Pro Tools-specific wrinkle is that [URL='https://goldmidi.com/community/threads/your-daw-picks-the-32classic-sidechain-format-for-you.76254/']plug-in aux outputs do not become sidechain sources[/URL], so route the source through a bus when another processor needs to hear it. The key path is also not a second full stereo audio feed. A [URL='https://goldmidi.com/community/threads/pro-tools-needs-a-different-deltascope-routing-trick.78002/']mono Pro Tools key input[/URL] is perfectly useful for detector jobs because the compressor mainly needs level and timing information. Problems appear when a plug-in expects the sidechain to preserve a complete stereo image rather than merely tell a detector when to move. [HEADING=2]Make the envelope fit the collision[/HEADING] How to sidechain kick and bass in Pro Tools gets easier once you stop treating threshold as the whole effect. Put the compressor on the bass, send the kick to its key input, then adjust sidechain compressor settings around the actual overlap. Attack determines how quickly the bass gets out of the way, while release decides how quickly it returns after the kick stops driving the detector. For a transparent fix, aim for only enough gain reduction to clear the kick. The broader [URL='https://goldmidi.com/community/threads/how-to-sidechain-kick-and-bass-cleanly.78389/']kick and bass sidechain relationship[/URL] matters more than copying somebody else’s ratio or release time because long kicks, short kicks, sustained bass notes, and syncopated patterns all hold the detector differently. Faster is not automatically cleaner. Sidechain compression on vocals in Pro Tools follows the same logic but usually wants less obvious movement. A lead vocal can key a pad, guitar bus, or backing-vocal group so those parts dip while the line is active. Slow the action enough that consonants do not make the whole mix twitch, and keep the gain change small unless audible pumping is part of the arrangement. [HEADING=2]Sidechaining is useful beyond full-band ducking[/HEADING] Learning how to sidechain reverb in Pro Tools usually means placing a compressor after the reverb and keying it from the dry source. The effect stays quieter during the phrase and rises as the dry sound falls away. You can sidechain delay in Pro Tools the same way, which keeps repeats from piling over the source without lowering the delay for the entire section. How to sidechain EQ in Pro Tools is a different decision because sometimes only one frequency area is colliding. Full-band compression turns the whole target down, while [URL='https://goldmidi.com/community/threads/scaler-eq-pro-compressors-and-dynamic-eq-do-different-jobs.78152/']sidechain dynamic EQ[/URL] can move a narrower region when the trigger appears. If only the bass fundamental clashes with the kick, reducing the entire bass may be more processing than the problem needs. Sidechain compression versus volume automation comes down to what should control the move. A compressor follows the trigger’s level and envelope, so changing kick dynamics can change the amount or duration of ducking. Automation or a programmed volume shape is more predictable when you want the same dip every time regardless of trigger level. When to use sidechain compression also matters at export. Printed ducking can be part of the production, but it can become an unwanted dependency when another mixer expects dry material. [URL='https://goldmidi.com/community/threads/how-to-export-stems-in-fl-studio.78448/']Stems with sidechain processing already working[/URL] should be checked as a system, because removing the trigger later can change the balance of a stem that was rendered while reacting to it. [/QUOTE]

Name