ADDAC System has launched two guitar clamps that let players make their strings vibrate without plucking them. The ADDAC006 Rotary Exciter Clamp and ADDAC007 Resonator Clamp bring some hands-on sound control to electric guitars and other string gear. And neither needs a full Eurorack rig to get involved.
The ADDAC006 uses a brushless motor rated at 7,000 RPM to set guitar strings in motion through magnetism. It fits near the spot where the neck meets the body. Rather than strike the strings, its spinning magnetic field makes them react at certain pitches and overtones. Quite a neat trick for sound design.
Players can tweak the motor with a speed dial that has a nonlinear response. Moving the clamp nearer or farther from the strings changes the result, while new guitar tunings add more options. There's room for a fair bit of trial and error here, which is half the fun.
Power is simple enough. A regular 9V DC pedal supply runs the rotary unit, and ADDAC packs a 5-meter extension lead for pedalboard use. That gives guitarists some room to place their gear without a short cable getting in the way.
Meanwhile, the ADDAC007 takes a different route. It grabs the guitar's headstock and uses an incoming audio feed to make the instrument resonate. The sound doesn't just come from a speaker. The guitar itself reacts to the signal, with its body and strings taking part.
Placement matters a lot with this one. Moving the clamp a little or turning it can change the tone quite a bit. The regular model grips headstocks as thick as 20 mm, while the wider ADDAC007W can fit surfaces up to 45 mm. That gives players more ways to try it on other gear.
Both clamps accept modular signals and standard line-level audio, which makes them useful with synths and other sound sources. The idea follows ADDAC's Four String Series, which brought real strings and pickup-style tools into Eurorack setups. These new units shift that approach onto the guitar itself.
As for cost, the Rotary Exciter sells for €120, while the Resonator costs €200. Both have gone on sale. They're niche tools, sure, but guitarists who like odd tones, drone sounds, and hands-on experiments have some fresh gear to play with.
The ADDAC006 uses a brushless motor rated at 7,000 RPM to set guitar strings in motion through magnetism. It fits near the spot where the neck meets the body. Rather than strike the strings, its spinning magnetic field makes them react at certain pitches and overtones. Quite a neat trick for sound design.
Players can tweak the motor with a speed dial that has a nonlinear response. Moving the clamp nearer or farther from the strings changes the result, while new guitar tunings add more options. There's room for a fair bit of trial and error here, which is half the fun.
Power is simple enough. A regular 9V DC pedal supply runs the rotary unit, and ADDAC packs a 5-meter extension lead for pedalboard use. That gives guitarists some room to place their gear without a short cable getting in the way.
Meanwhile, the ADDAC007 takes a different route. It grabs the guitar's headstock and uses an incoming audio feed to make the instrument resonate. The sound doesn't just come from a speaker. The guitar itself reacts to the signal, with its body and strings taking part.
Placement matters a lot with this one. Moving the clamp a little or turning it can change the tone quite a bit. The regular model grips headstocks as thick as 20 mm, while the wider ADDAC007W can fit surfaces up to 45 mm. That gives players more ways to try it on other gear.
Both clamps accept modular signals and standard line-level audio, which makes them useful with synths and other sound sources. The idea follows ADDAC's Four String Series, which brought real strings and pickup-style tools into Eurorack setups. These new units shift that approach onto the guitar itself.
As for cost, the Rotary Exciter sells for €120, while the Resonator costs €200. Both have gone on sale. They're niche tools, sure, but guitarists who like odd tones, drone sounds, and hands-on experiments have some fresh gear to play with.